Belowground Horizontal Grease Arrestor

Belowground Horizontal Grease Arrestor

Model Range

service
B.GH.1000.C

Diameter – 1050mm
Length – 1800mm

Download Specs and Drawing Page

service
B.GH.1500.C

Diameter – 1050mm
Length – 2500mm

Download Specs and Drawing Page

service
B.GH.2000.C

Diameter – 1200mm
Length – 2400mm

Download Specs and Drawing Page

service
B.GH.3000.C

Diameter – 1200mm
Length – 3500mm

Download Specs and Drawing Page

service
B.GH.4000.C

Diameter – 1500mm
Length – 2800mm

Download Specs and Drawing Page

service
B.GH.5000.C

Diameter – 1500mm
Length – 3500mm

Download Specs and Drawing Page

Victoria Model Range

service
B.GH.600.V

Diameter – 1050mm
Length – 1200mm

Download Specs and Drawing Page

service
B.GH.1100.V

Diameter – 1050mm
Length – 2000mm

Download Specs and Drawing Page

service
B.GH.2000.V

Diameter – 1200mm
Length – 3000mm

Download Specs and Drawing Page

service
B.GH.3000.V

Diameter – 1200mm
Length – 3500mm

Download Specs and Drawing Page

service
B.GH.4000.V

Diameter – 1500mm
Length – 2800mm

Download Specs and Drawing Page

service
B.GH.5000.V

Diameter – 1500mm
Length – 3500mm

Download Specs and Drawing Page

Installation

Lifting and Tank Handling from Truck

Once the truck arrives:

1. Check condition of the tank to ensure no damage has incurred in Transport. All issues must be photographed and sent to AUSTERE PUMPS for verification.

Lifting procedure:

2. Place Soft Slings around the body of the station
3. Slings to be ¼ from each end
4. Connect two leg chains to slings
5. Ensure that angle of lifting is no less than 60 degrees.
6. Lift and Place on Ground
7. Place tank on ground as the same Position of the truck
8. Ensure that the tank is resting on supports. Ensure that the flanges do not come in to contact with the ground.
9. Ensure that the base of the tank is on soft ground (I.E. grass)

Below Ground Horizontal Installation

With Feet
Feet can be provided during manufacture to enable the tank to be placed on a flat concrete base and levels checked prior to surrounding with concrete. Feet are not load bearing and minimal water should be placed in the tank prior to placing backfill concrete.

  1. Pour concrete base to correct depth and level off. Base to be reinforced as necessary
  2. When this concrete has set sufficiently, place the tank into position, check for levels including outlet and inlet inverts and fill with water in accordance to the details given. Ensure concrete slab is clean and ready for placing concrete surround. Ensure placement of surround within 48hrs of casting the base slab.

Without Feet

  1. Determine the size of the excavation from the dimensions of the tank and the incoming drain invert depth allowing for a minimum of 200-250mm of concrete around the tank.
  2. Excavate allowing for easy placing of the tank and concrete and for consolidating concrete around the bottom half of the tank when backfilling.
  3. Place concrete along the centre of the excavation vase and lower the tank into position ‘puddling’ it into the concrete to form a cradle. Consolidate under the tank to prevent voids by hand, do not use vibrating pokers.
  4. Check that the tank is truly vertical and level and that the inlet and outlet levels are correct
  5. After the concrete has reached its initial set, fill with water according to the given data
  6. Continue by placing concrete around the tank at the same time filling with water to equalise pressure and resist flotation. Where the tank is divided into chamber ensure all chambers are equally filled.
  7. Connect pipework, seat access shaft into socket and apply waterproof mastic and adhesive, or as applicable.
    Top up the tank with water to the invert level and place the remained of the concrete to a depth of approximately 250mm above the top of the tank. Where extension shafts are fitted1. these can be surrounded in concrete once the main tank surround concrete has been set. IMPORTANT: Before surrounding circular or rectangular shafts with concrete, shutter internal to support the sides and safeguard against distortion.
  8. Where the concrete slab over the tank is to take the vehicle loading, it should be reinforced, in accordance with good practice to take the maximum load. The reinforcing should be extended onto unexcavated ground. It is important that vehicle loading is not transferred to the tank itself.